Search found 9 matches

by nsnape
Sun Jun 29, 2003 7:23 am
Forum: Heidelberg (ex Linotype)
Topic: [bCIRCON LENSES PROBLEM
Replies: 11
Views: 8489

Hi Ray,
Nice to see you here on this forum too.
The 6.0.2.33 was put up on the site for the registered users about two weeks ago. Works great. Too bad Lasersoft didn't make a version for my ICG drum scanner :-?
by nsnape
Wed Jun 18, 2003 12:07 pm
Forum: Heidelberg (ex Linotype)
Topic: [bCIRCON LENSES PROBLEM
Replies: 11
Views: 8489

Yes , bravo to the Lasersoft developers, a work well done deserves much credit.
It works beautifully on the Circon prolonging the life of this old scanner with first grade up to date software. :D
by nsnape
Fri May 16, 2003 7:30 am
Forum: OSX - JAGUAR Problems
Topic: SilverFast on OSX2.2
Replies: 12
Views: 9128

I'm running on Jaguar 10.2.6 with absolutely no technical problems. Sometimes deep sleep and the SCSI card can have problems yet those are issues between port comm and MacOsX. Note: the scanner must be turned on before booting (not just logout/in) and thereafter it will be seen , even after sleep. O...
by nsnape
Sat May 10, 2003 8:55 pm
Forum: Heidelberg (ex Linotype)
Topic: [bCIRCON LENSES PROBLEM
Replies: 11
Views: 8489

It's actually the mid lens the 1200 dpi lens that isn't yet supported. Other than that I've been getting very good scans , especially from negs with Silverfast. The only draw back is scanning prints with the 800 dpi lens as on the Circon it's not very sharp. Hopefully this mid lens support will be m...
by nsnape
Sat May 10, 2003 8:48 pm
Forum: Heidelberg (ex Linotype)
Topic: linotype scanner TOPAZ 1
Replies: 19
Views: 21880

That'd be good if Lasersoft will support the Topaz series.
Heidelberg do have Newcolor 7000 V2.54 for MacOsX that turns these scanners. It is very expensive and buggy on MacOsX whereas PC runs well.
by nsnape
Mon May 05, 2003 11:16 pm
Forum: About SilverFast
Topic: Prescan Color Not Close With Negatives Shot In Studio
Replies: 3
Views: 1372

Good idea.
Could this also be a way to scan for contacts sheets?
I was trying to do just that the other day but gave up and printed darkroom contacts as the spaces between the negs was playing with the base color set up.
by nsnape
Mon May 05, 2003 11:10 pm
Forum: Heidelberg (ex Linotype)
Topic: Circon is seen but can't keep the connection
Replies: 2
Views: 5236

8) The r17 version has fixed almost all problems with connectivity. If the scanner is turned on at boot time, Silverfast continues to work even after many deep sleep cycles. Bravo Lasersoft. Hope the middle lens for the Circon will be available soon too. I just had about 30 full page magazine work p...
by nsnape
Sat Feb 01, 2003 12:26 am
Forum: Heidelberg (ex Linotype)
Topic: Circon is seen but can't keep the connection
Replies: 2
Views: 5236

Spoke too soon. Fiddled with the SCSI cable unplugged and replugged the terminator in, rebooted and launched the stand alone. It now works albeit a few UI bugs so far.Happy to be scanning in OSX finally. For any others I'll have to say that the SCSI connections are even more important than ever to v...
by nsnape
Fri Jan 31, 2003 11:44 pm
Forum: Heidelberg (ex Linotype)
Topic: Circon is seen but can't keep the connection
Replies: 2
Views: 5236

Circon is seen but can't keep the connection

:( I just downloaded the SF 6,01 for the Circon. I was so hoping that it'd work. Alas, not in Jaguar Quicksilver 867 all the latest firmware etc.. The scanner is seen with the Adaptec 2906 card in system profiler. SF starts up and of course installed fine. The overview scan starts but blocks at abou...

Go to advanced search